I/P CONVERTERS |
|||||||
The I/P bolt on kit used here is directly interchangeable with one used on the positioner. | |||||||
The standard range is 4-20mA = 20-100kPa. Please note: other ranges may effect price and delivery | |||||||
STANDARD (NON - I/S) Including a 5 micron filter | |||||||
Retrofit mounting kit c/w u-bolts and feedback | |||||||
ANCILLARIES | |||||||
Instrinsically safe SABS - (SABS - Ex ib IIC T6) | |||||||
Mounting hardware (2" pipe bracket powder coated mild steel) | |||||||
mounting hardware (Plate only powder coated mild steel) | |||||||
ACTUATOR POSITION FEEDBACK - with the positioner | |||||||
This module is designed to fit onto our positioner. The old lid is replaced and the feedback module | |||||||
is mounted to a new lid. Alternatively, the module can be supplied as a loose unit with a NAMUR | |||||||
bracket. | |||||||
Digital feedback - switch boxes (for on/off indication) | |||||||
Mechanical type | (2 mechanical micro switches (V155 1 A5 220V, 15A) | ||||||
Proximity type (3 wire PNP DC with amplifier | (2 proximity switches (P+F: NBB2-V3-E2-24V DC) | ||||||
Proximity type (2 wire 24V DC) | (2 proximity switches (P+F: NBB3-V3-Z4-24V DC) | ||||||
Proximity type ( Ex is IIC T6 2 wire Namur type) | (2 proximity switches (P+F:NJ2-V3-N-8V DC) | ||||||
FULL ANALOG FEEDBACK (for continuous indication) | |||||||
4 - 20mA (standard) | suitable for a 2 wire 4 - 20mA feedback in a non-harzardous environment | ||||||
4 - 20mA (I/S) SABS certified to Ex ib IIC T4 | |||||||
RECOMMENDED SPARES | |||||||
I/P module | I/P module | (Samson Ex ia IIC T6 - without adaptor plate) | |||||
KIT 7 | Range lever kit | ( A complete range lever kit) | |||||
KIT8 | Primary lever kit | (A complete primary lever kit) | |||||
KIT 9 | Seal kit | (All o-rings, seals and diaphragm | |||||
KIT 10 | E-clip kit | (All E-clips in stainless steel) | |||||
KIT 11 (s) | I/P module | (Samson Ex ia IIC T6 - PTB with adaptor plate and | |||||
terminal block) | |||||||
KIT 11 | I/P module | (Samson Ex ia IIC T6 -PTB with terminal block | |||||
KIT 14 | Spool assembly | (With spool retainer block, o-rings amd screws) | |||||
KIT 14 (s) | Spool assembly | (Only spool block and spindle) | |||||
NP | Pneum blanking plate | (Blanking off palte, o-rings and screws) | |||||
PP or PM | Pneum bolt on kit | (Signal block, gauge, screws, 1/4" plugs and o-rings) | |||||
EP or EM | I/P bolt on kit | (kit 11 module, housing, screws and o-rings) | |||||
CAM | Std or split range cam | ||||||
CAMSHAFT | International shaft | ||||||
GAUGE | (0-1000kPa or 1 -160kPa) | ||||||
FILTER | (5 micron, 1/4" pipe, manual drain without a nipple) | ||||||
DIAPHRAGM | (For the positioner) | ||||||
POSITIONER LID | (Window lid) | ||||||
I/P FILTER PLUG | (Presses into the I/P base) | ||||||
LINEAR LONG BEARING KIT | (5x 604 bearings, 8x retainer disk & 5x M4 nylocs) | ||||||
P0289 | AFB board | (PC board for the analogue feedback module) | |||||
P0259 | AFB potentiometer | (Potentiometer for the analogue feedback module) | |||||
SERVICE AND REPAIRS | |||||||
Positioner service | (Strip, clean, replace all seals & any damaged parts except I/P, | ||||||
spool assembly and gauges) | |||||||
Casting enclosure | (Box, lid and other parts for P/P) | ||||||
I/P enclosure | (I/P base and lid complete with filter plug) |